Search published articles
Mohammad Mahdi Aminpour1, Mohammad Maleki,
Volume 14, Issue 1 (5-2020)
Volume 14, Issue 1 (5-2020)
Abstract
Introduction
Studying the effect of slope angle on bearing capacity of foundations on the slope in urban areas is a challenging problem that has been investigated by researchers for years. In general, the analytical approaches for solving this problem can be categorized into limit equilibrium, characteristics and limit analysis methods. In recent years, there have been studies for using the limit analysis within the framework of finite element method for geomaterials. In these studies, the soil mass is not considered as rigid and there is no need to predefine a failure surface for the slope. In the performed research, using the upper bound finite element limit analysis, bearing capacity of strip foundation on slope have been studied. This analytical method enables the use of the advantages of both methods of limit analysis and finite element analysis. In this method, the slip between the two elements is considered. In order to find the critical state of the failure, the rate of power internally dissipated is linearly optimized, by using the interior points method. The advantages of this method are the high convergence rate in comparison with other analytical optimization methods. The effect of different upstream and downstream slopes and foundation depths and also the influence of various mesh discretizations have been evaluated. Finally, the results are compared with those obtained from previous methods available in the literature.
Methods
The finite element limit analysis method is based on nodal velocities. Considering the principals of the finite element method and having the nodal velocities, the velocity at each node of the element can be obtained from corresponding shape functions. The rate of power internally dissipated in each element is defined by multiplying the strain rate on stress in each element. In this method, the slip between the two elements and the rate of internal power dissipated at each discontinuity of two adjacent elements is considered. For this purpose, in each node, four new unknowns’ velocities are defined. To remove the stress from the equations, and provide a linear relationship for linear optimization, a linear approximation to the yield function has been used. For this purpose, the Mohr-Coulomb yield criterion is estimated with a polygon in the stress space. Also, using the reduced strength parameter, the effect of the dilation angle is considered. According to the principles of upper bound limit analysis, the value of plastic strain rate is calculated from the flow rule. The velocity field in elements and discontinuities must satisfy the set of constraints imposed by an associated flow rule. In order to have an acceptable kinematics field, the velocity vectors have to satisfy the boundary conditions. These conditions include zero kinematics velocities along the vertical and horizontal boundaries of the geometry as well as negative vertical unit velocities and zero horizontal velocities at points underneath the rigid foundation.
Results and discussion
In order to calculate the bearing capacity of foundation, a set of different uniform and non-uniform mesh has been examined. The results obtained from different uniform mesh sizes indicate a certain divergence in the course of analysis. However, the results between the fine and very fine non-uniform mesh are closely related to each other and are converged. The obtained results show that, by increasing the internal friction angle, the bearing capacity has been increased. At high angles of modified friction, the effect of increasing the internal friction angle on the increase in bearing capacity is more in slopes with lower angles. By increasing the downstream foundation depth, the bearing capacity has been increased. This increase is more important in the case of slopes with lower angles. However, the upstream depth variations didn't present a significant effete on bearing capacity. In order to investigate the effect of upstream angle on the bearing capacity, the upstream mesh is also refined similar to the downstream. The obtained results indicate that variations of the upstream angle have a minor effect on the bearing capacity. This is of course true if the upstream slope is fully stable. The results of the proposed method in this study are an upper bound for the results reported by the limit equilibrium and displacement finite element methods. As seen in Figure 1, the suggested method predicts lower bearing capacities compared to rigid block limit analysis method and is indeed a lower bound for the classical limit analysis method. The finite element limit analysis with linear optimization has resulted in more bearing capacity than cone optimization. The bearing capacities, obtained from characteristic lines method depending to the slope angles, in some cases is more and in some cases less than those explored by the proposed method.
In this paper, the bearing capacity of foundation located on slope was evaluated by finite element limit analysis method. In this regard, the effects of different downstream and upstream angles of slope and foundation depths and also, the effect of various mesh discretizations on the bearing capacity were studied. It is shown that an increase in the downstream angle causes a decrease in the bearing capacity and an increase in the downstream foundation depth leads to an increase in the bearing capacity. However, the upstream angle and upstream foundation depth were not much effective on the bearing capacity.
Ahmadreza Mazaheri, Ali Noorzad,
Volume 14, Issue 2 (8-2020)
Volume 14, Issue 2 (8-2020)
Abstract
Introduction
The use of various additives to improve the properties of soils from past years have been studied by different researchers. Such additives are lime, cement, fly ash and fiber which have been used frequently in combination with soil. Lime is one of the oldest additives that it is utilized with different types of soils. Lime has positive impact on geotechnical properties of soil that alter some of the soil characteristics. Adding lime causes to reduce plasticity ranges, enhanced efficiency, strength and shrinkage of the soil. Extensive researches in the field of sustainability of clay with lime indicate that the optimum percentage of lime in the soil modification is between 1 to 3% by weight of the soil. But some researchers believe 8% by weight of lime are effective for soil stabilization. The presence of lime in clay soil yiels to occur some reaction, that it improves the soil properties. Reactions are included cation exchange flocculation, carbonation and pozzolanic reactions. Cation exchange between the clay cations and calcium cations takes place in lime. Cation exchange causes clay particles to get closer to each other creating complex structures in the clay soil and this improves the clay soil features. In recent years the use of nanoparticles is considered in civil engineering field. The investigations have demonstrated that the use of nanomaterial increases cement reactivity and also improves density because it is filled with particles. Recent research has shown that the use of montmorillonite nano-clay soils to control swelling and to reduce failure potential in the soil. A number of researchers have expressed the use of nanoparticles causes to decrease the hydraulic conductivity of soils. In this paper, the effect of nano-clay and lime on the important soil parameters is evaluated. For this purpose, lime at 2 and 4 percentage and nano-clay at 0.5, 1 and 2 percentages have been added to clay soil and their impact on parameters such as optimized moisture, Atterberg limits, unconfined compressive strength and self-healing properties of soil is evaluated. Self-healing properties is one of the features, to repair damages due to internal erosion in the clay which is very efficient and important.
Materials and experimental methods
In the present research, the effect of lime and montmorillonite nano–clay to soil strength is evaluated. For this purpose, samples of clay soil (CL) has been used. In the experimental study, the percentages of additives mixed with the dry soil and then the optimum moisture and maximum specific weight of soil are determined with different percentages of additives. Soil Atterberg limits based on the ASTM D4318 standard have been determined. Dry samples have been mixed together and then the water is added and mixed well with each other. Then the sample has been prepared in the form of a steel cylinder (cylindrical specimens) with a diameter of 50 mm and a height of 100 mm. Specimens were molded immediately and the weight and dimensions were carefully measured and then placed in plastic to prevent moisture loss and put them at 20 °c and 90% moisture curing room.
Results and discussion
In this study, the percentage of lime is between 0, 2, 4 percent by weight and nanomaterials percentage is between 0.5 and 1 and 2 percent that can be varied in order to analyze the effect of various additives on the properties of the soil samples. The results indicate that increasing the nano-clay and lime percentage can enhance the optimum specific gravity of soil. The optimum moisture content of sample without any additive is equal to 19.5%. However, samples contain 2% nano-clay and 4% lime, the optimum moisture content increases to 23.5%. But the presence of lime reduces the maximum dry density of soil while adding nano-clay increases this amount. In samples with 4% lime and with no nano-clay, maximum dry density is 17
but in case of lime with 4% and nano-clay with 2% it is increased to 17.5 . In addition, adding lime without the presence of nano-clay only increases strength of soil. When 2 percent of lime is added, the strength of soil increases about 39 percent. As mentioned before, the effect of lime and nano-clay on increasing of unconfined compressive strength is almost the same which means by adding 2% of lime or nano-clay the strength of the soil increases about 40 percent. Using both lime and clay nanoparticles simultaneously (each 2%), a significant increase in strength of soil occurs in approximately 77 percent.Conclusion
The use of nano-clay and lime improves soil strength parameters. But economically lime is more affordable than nano-clay. Therefore, if you need to increase only unconfined compressive strength, then the nano-clay is not recommended.
When it comes to self-healing in clay, the nano-clay can improve resistance rupture of the soil. By adding 2% of nano-clay in soil, healing of soil resistance after the break and after 24 hours can reach up to 60% of the ultimate strength of the soil. This property can be used to repair of locations that are subjected to internal erosion and scouring.
Shima Sadat Hoseini, Ali Ghanbari, Mohammad Ali Rafiei Nazari,
Volume 14, Issue 2 (8-2020)
Volume 14, Issue 2 (8-2020)
Abstract
Introduction
The discussion of modeling the interaction of soil-pile groups due to a large number of parameters involved in is one of the complex topics and it has been one of the interests to researchers in recent years and has been dealt with in various ways. In recent years, the artificial neural network method has been used in many issues related to geotechnical engineering, including issues related to piles.. In this study, firstly it was tried to explain the importance of soil - structure interaction in calculating the dynamic response of bridges. Then, the effect of different effective parameters in calculating the interaction stiffness of the pile - soil group using artificial neural network was studied. For this purpose, firstly, Sadr Bridge ( The intersection of Modarress and Kaveh Boulevard because the presence of tallest piers ) in the transverse direction, considering and without considering of the effect of soil - structure interaction was analyzed. The analysis was carried out in which the substructure soil was replaced with a set of springs and dashpots along the piles. Considering the fact that many factors are involved in determining the equivalent stiffness of springs, in the second stage, the effect of different factors on the stiffness of spring equations using artificial neural network was investigated. Finally, the artificial neural network method was used as a suitable method in order to estimate the equivalent stiffness values, the equivalent stiffness of the pile - soil group was introduced for different input values. equivalent stiffness of the substructure soil using the artificial neural network ,has not been used by researchers yet, so estimation of the optimal length and diameter of piles used in constructions and estimating the seismic performance of the bridge system after its implementation could be effective .
Material and methods
In this paper, spring-dashpot method is proposed to the non-uniform analysis of single-pier bridges which led to a 5-degree freedom model in the case of Sadr Bridge. This study also endeavors to investigate the SSI effect in dynamic analysis of bridges. This method is based on the traditional spring-dashpot method but in this method, non-linear stiffness is used along the piles, instead of linear stiffness and upgraded shape functions and coefficients are applied to make more precise mass, stiffness and damping matrices. Then the seismic responses of Sadr Bridge are compared in different conditions including or excluding the SSI effects. Considering the fact that in the present study to calculate the stiffness of the soil-pile group at depth, due to the effect of soil - structure interaction, the recommended method by API is used, the study of neural network analysis was used and the effect of different parameters used to determine the complexity of the soil-pile group system has been evaluated. The multi-layer feeder network, which has the most application in engineering issues, has an input layer, an output layer and one or more layers of hidden content, has been used for this purpose. The best model of the neural network with a topology of 1-20-6 was provided using the hyperbolic sigmoid activation function, and the Levenberg Marquardt model and the training cycle 84, which had the least error mean square and the best regression coefficient. The effect of internal friction angle, soil density, pile diameter and the resistance per unit length has been evaluated with this method.
Results and discussion
[8] ارائه شده است صورت می پذیرد In this study, the importance of considering the effect of soil - structure interaction on the dynamic response of the Sadr Bridge was studied. Dynamic stiffness of the soil around the pile group was calculated based on the equivalent linear method and using the p-y springs. So, the effect of substructure soil was considered in dynamic analysis of the system . The artificial neural network was used to predict the stiffness of the soil - pile group, based on various input parameters and the stiffness sensitivity analysis of the calculated output values was conducted. In hard soils, the stiffness of the pile - soil group increases with increasing the diameter of the pile in the range of 1 to 1.5 m in diameter. However, in the range of 0.5 to 1 m in diameter, the diameter of the pile does not have much effect on the stiffness of the system and also stiffness decreases in the range of 1.5 to 2 m in diameter by increasing the pile diameter. Soil specific weight and angle of internal friction can change the system stiffness but the effect of the soil specific density is much greater on the stiffness of the soil-pile group system. Generally, the specific density in the range of 1000 to 2300 (kg/m3) will increase the stiffness of the system. In general, the ultimate strength of the soil among 100 to 550 (kN/m) affects the system stiffness. This effect within the ultimate strength between 100 and 220 (kN/m) causes increasing in the interaction stiffness value of the system and in the range of 220 to 550 (kN/m) causes reducing the stiffness of the system . The ultimate strength values in a unit of length outside of the above range have little effect on the system interference stiffness. Despite the fact that the problem of calculating the soil - pile interaction stiffness is a direct solution, the use of the proposed neural network model can help in predicting optimal values of diameter and length of the pile to achieve maximum soil- pile stiffness and especially for long bridges it will has a significant impact on reducing cost and seismic design of the bridge.
Conclusion
The results of this study are as follows:
The results showed that considering the interaction effect, although it increases the relative displacement of the deck, reduces the maximum base shear and moment. This suggests that considering the maximum base shear and moment in the interaction conditions may not lead to a seismic design for certainty, although closer to reality.
Artificial neural network is an efficient way and new method to predict the stiffness of the soil-pile group system based on different input values that have not been used yet. So that with the physical and mechanical properties of the soil as well as the geometric properties of the piles, it is possible to predict the interaction stiffness values with the proper precision.
According to the results and diagrams obtained from the neural network model, which are mainly sinusoidal, the optimal values of the interaction stiffness can be obtained by obtaining the pile diameter, specific gravity, the internal soil friction soil to achieve optimal interaction strength. It is also possible for each site to estimate the depth of the piles in order to achieve optimal hardness.
./files/site1/files/142/4Extended_Abstracts.pdf
Hadi Bahadori, Amin Khalili,
Volume 14, Issue 2 (8-2020)
Volume 14, Issue 2 (8-2020)
Abstract
Introduction
Soil dynamic properties are used to evaluate the dynamic response of soils at different strain levels in geotechnical engineering. The shear modulus (G) and damping ratio (D) are among the most important dynamic properties of soils. In general, the factors affecting the dynamic behavior of soils are divided into two categories: first; soil type and characteristics such as water content, void ratio and soil plasticity and second; parameters of loads applied on the soil such as the number of loading cycles, loading frequency and loading waveform .Therefore, it is widely believed that the dynamic response of soils partially depends on the characteristics of the load. In this paper, 1-g shaking table tests were employed to investigate the effect of loading waveform and frequency content on dynamic properties of dry sands. The response obtained from soil samples during loading with different frequencies, input accelerations and waveforms were used to generate hysteresis loops of tested samples at different strain amplitudes. Then, hysteresis loops were used to determine the damping ratio and shear modulus at different strain levels. Finally, the effects of loading frequency and waveform on the changes of each parameter (G and D) were investigated.
Material and methods
A hydraulic shaking table with a single degree of freedom, designed and constructed at the Crisis Management Center of Urmia University, was used to conduct the experiments. Firoozkuh No. 161 sand was used in all the experiments. The Firoozkuh sand gradation curve is similar to that of Toyoura sand. In this study, accelerometers were used to measure the acceleration of the input to the sample as well as to record the acceleration caused by the input excitation at different depths of the soil sample. The displacement transducers (LVDT sensors) were also used to measure linear displacement. Each soil sample was constructed using dry Firoozkuh sand poured uniformly into the container from four equal heights of 150 mm to reach a total height of 600 mm. During the compaction process, the accelerometers A1, A2, and A3 were placed at a depth of 150, 300 and 450 mm with respect to the bottom of container. Also, one accelerometer, A0, was attached rigidly to the container base to measure base acceleration. A displacement transducer (L1) was placed on the soil surface at a height of 600 mm from the floor of the container to measure the vertical displacement of the surface of the soil. In this study, 42 shaking table tests were performed to study the effect of loading frequency and waveform on dynamic properties of dry sand. The test samples were subjected to rectangular, sinusoidal and triangular loading at frequencies of 0.5 to 9 Hz and at input acceleration of 0.1g and 0.3 g.
Results and discussion
Given the importance of G-γ and D-γ curves in dynamic analyses, the changes in shear modulus with shear strain has been studied. The results show that the shear modulus increases as the frequency increases in all cases, and this increase is observed at lower frequencies and increases with increasing frequency. On the other hand, the shear modulus decreases with increasing shear strain. At a constant testing frequency, soil samples subjected to the rectangular waveform exhibited the largest shear modulus while the samples subjected to the triangular waveform showed the least shear modulus. The shear modulus of the samples under the sinusoidal waveform is barely more than the shear modulus of samples under triangular waveform. Moreover, by increasing the shear strain, the shear modulus values of samples with different waveforms have become closer and the waveform effect is reduced. As for the effect of input acceleration on the shear modulus , increasing the input acceleration increases the shear strain and consequently, decreases the shear modulus in all states (the values of shear modulus in various frequencies and the waveforms under the input acceleration of 0.1 g are larger than the shear modulus values under the input acceleration of 0.3g). In the case of the damping ratio, the results show that, in all cases, damping ratio increases with shear strain. At low strain levels, the damping ratio values at various frequencies and waveforms are low and yet very close. At higher strain levels, the increase in frequency increases the damping ratio. This increase is more significant at higher frequencies. Also, the effect of waveform on the damping ratio is more apparent at larger shear strains, and at such shear strain levels, soil samples under rectangular loading exhibit the largest damping ratio. The damping ratio associated with the sinusoidal and triangular loading are also close to each other and it is a slightly larger for sinusoidal loading. On the other hand, the damping ratio increases with input acceleration. In addition, the effect of increased input acceleration on the increase in the damping ratio is more obvious at higher frequencies mainly due to the increase in shear strain.
Conclusion
In the present study, the effects of loading frequency and waveform on the dynamic properties of dry sand were investigated using shaking table tests. The following conclusions were drawn:
- The shear modulus increases with frequency. The trend is more obvious at larger frequencies. The effect of loading frequency on the damping ratio of the soil at low levels of strain is negligible, and at relatively large strain levels, damping ratio increases with loading frequency.
- Soil samples exhibit the highest shear modulus and damping ratio under rectangular loading. Therefore, in all the tested frequencies and input accelerations, the values of G and D for the rectangular waveforms are greater than those of the sinusoidal and triangular waveforms. The shear modulus and damping ratio for the sinusoidal waveforms are marginally greater than those of triangular waveforms, yet one can consider them practically similar.
- In all cases, the shear strain increased by increasing the amplitude of the input acceleration, and as a result, the shear modulus decreased and the damping ratio increased../files/site1/files/142/2.pdf
Javad Akbardoost, Jamal Bidadi,
Volume 14, Issue 2 (8-2020)
Volume 14, Issue 2 (8-2020)
Abstract
Introduction
Rock masses have an enormous geometrical discontinuities such as void, notch, crack and flaw. These geometrical discontinuities which play as stress concentrator, cause to reduce the load bearing capacity of rock masses. In rock masses, the crack is the most important geometrical discontinuity assessed frequently by civil, mechanical and mining engineers and researcher. The fracture mechanics which is a branch of mechanical engineering science, has been often used for investigating the cracked rock samples. The fracture toughness is one of the important parameters in the fracture mechanics which describes the resistance of materials against the crack growth. On the other hand, since orientation of cracks relative to the loading directions can be arbitrary, brittle fracture in rocks may happen due to a combination of two major fracture modes, i.e. crack opening mode (mode I) and crack sliding mode without any opening or closing the crack flanks (mode II). In order to obtain the fracture toughness of rocks, several test configurations under pure mode I have been proposed. One of the parameters that has the influence on the fracture toughness of rocks and other materials is the thickness of test sample. Previous experimental results showed that the fracture toughness of rocks increases by increasing the specimen thickness until a specific thickness. After that, the fracture toughness decreases for thicker samples until plane strain condition occurs. Then, the fracture toughness becomes a fixed value when the thickness of sample varies.
The all preceding studies have been dealt with considering the effect of specimen thickness on fracture toughness focusing only the mode I fracture toughness and there is few research concerning the thickness effect on the mode II fracture toughness of rocks. Therefore, the aim of this paper is to investigate experimentally the effect of specimen thickness on the mode II fracture toughness.
Material and methods
To investigate the thickness effect on the mode II fracture toughness of rocks, several fracture tests were conducted on the semi-circular bend (SCB) specimens. The SCB specimen is a semi-disk of radius R and thickness t including an edge crack of length a loaded under three-point bending. When the crack is along the applied load and the bottom supports are symmetric relative to vertical crack, the SCB sample is under pure mode I loading. One of the methods for achieving the mixed mode loading in SCB sample is the asymmetry distances of bottom supports from the vertical crack located at the middle of bottom edge (see Figure 1). The pure mode II in this type of SCB sample is attained at a specific distances, i.e. at specific values of S1 and S2. These values of supporting distance can be obtained from finite element analysis.
Figure 1. The schematic of SCB sample.
The fracture tests were done both on pure mode I and pure mode II, for the sake of comprehensiveness. Therefore, 32 SCB samples with 4 different thicknesses and 4 repetition for each specimen size were tested for both pure mode I and pure mode II. The specimens were cut from Ghorveh marble sheets with different thicknesses by water jet machine. Then, the specimens were cracked artificially by a high speed rotary diamond saw blade. The specimen dimensions and loading conditions are presented in Table 1. Finally, the cracked SCB samples were tested by using a 300 kN ball-screw universal test machine. Table 1 also gives the average of four fracture loads (Pf) obtained for each thickness of specimen.
Table 1. The specimen dimensions and loading conditions.
| S.D. (N) | Pf (N) | S2 (mm) | S1 (mm) | a (mm) | t (mm) | R (mm) | |
| Pure mode I | 150 | 3220 | 57 | 57 | 28.5 | 15 | 95 |
| Pure mode II | 350 | 4726 | 11 | 57 | |||
| Pure mode I | 360 | 6711 | 57 | 57 | 28.5 | 25 | 95 |
| Pure mode II | 882 | 9445 | 11 | 57 | |||
| Pure mode I | 1450 | 20285 | 57 | 57 | 28.5 | 50 | 95 |
| Pure mode II | 4179 | 25441 | 11 | 57 | |||
| Pure mode I | 4672 | 31810 | 57 | 57 | 28.5 | 80 | 95 |
| Pure mode II | 4686 | 36848 | 11 | 57 |
The mode I and mode II fracture toughness (KIc and KIIc) can be calculated for SCB samples from following equations:
(1) 
(2)where Pf is fracture load, R and t are the radius and thickness of SCB sample, respectively KI* and KII* are geometry factors which depend on geometrical ratios a/R, S1/R and S2/R and independent of specimen dimensions and magnitude of applied load. These dimensionless parameters are often obtained from finite element analysis. For tested SCB samples, the values of KI* and KII* were extracted from previous studies as shown in Table 2. Substituting the fracture loads and specimen dimensions from Table 1 and the values of KI* and KII* given in Table 2 into Eqs. (1) and (2), the mode I and mode II fracture toughness were calculated as listed in Table 2. Figure 2 also shows the variations of mode I and mode II fracture toughness with respect to specimen thickness. As seen from this figure, the fracture toughness for both pure modes increases for thicker samples until a specific thickness. After that, the values of KIc and KIIc decrease by increasing the specimen thickness. For plane strain condition in which the thickness of specimen is relatively large, the values of KIc and KIIc are nearly constant.
Table 2. The dimensionless parameters KI* and KII* for tested SCB samples and their corresponding fracture toughness.
| KIIc (MPa.√m) | KIc (MPa.√m) | KII* | KI* | t | R | |
| Pure mode I | 0.0 | 1.125 | 0.0 | 0.644 | 15 | 95 |
| Pure mode II | 0.897 | 0.0 | 0.35 | 0.0 | ||
| Pure mode I | 0.0 | 1.411 | 0.0 | 0.644 | 25 | 95 |
| Pure mode II | 1.075 | 0.0 | 0.35 | 0.0 | ||
| Pure mode I | 0.0 | 2.126 | 0.0 | 0.644 | 50 | 95 |
| Pure mode II | 1.448 | 0.0 | 0.35 | 0.0 | ||
| Pure mode I | 0.0 | 2.083 | 0.0 | 0.644 | 80 | 95 |
| Pure mode II | 1.311 | 0.0 | 0.35 | 0.0 |
Figure 2. The variations of KIc and KIIc versus the specimen thickness.
Conclusion
The effect of specimen thickness on the mode I and mode II fracture toughness of rock was investigated experimentally using the SCB specimens. The experimental results showed that the fracture toughness for both pure modes increases when the thickness of specimen increases until a specific thickness. After that, the values of KIc and KIIc decrease by increasing the specimen thickness. For plane strain condition in which the thickness of specimen is relatively large, the values of KIc and KIIc are nearly constant. Also, it is shown the crack grows more curvilinearly for thicker SCB samples../files/site1/files/142/1.pdf
Semaneh Ghasemvash, Rouzbeh Dabir,
Volume 14, Issue 3 (11-2020)
Volume 14, Issue 3 (11-2020)
Abstract
Introduction
Pavement layers as a part of road structure play an important role and provide a flat and secure surface. Subgrade layer could act as a compacted embankment, natural or stabilized ground. Subgrade is a foundation of pavement layers, and it withstands all of loads due to vehicles that are transferred from upper layers (i.e., subbase, base and asphalt layers).Therefore, constructing pavements with bearing capability, high durability, quality, and maintenance in proper operating conditions is very important. However, suitable materials for constructing pavement layers are not available, and improvement techniques should be employed for them. Generally, different methods such as mechanical or chemical are available for improvement. Nowadays, geosynthetic materials such as geotextile and geogrid are used to optimize and enhance the bearing capacity of pavement layers. The present study is aimed to investigate the effects of geotextile applications on bearing capacity of clay-gravel mixtures in pavement layers.
Material and Methods
In this research, materials were prepared from Barandouz area. Clayey soil was mixed with gravel in 25, 50 and 75 percentages (by weight). Geotextile was woven and made of polypropylene (with commercial name Fibertex-F-32). Geotextile effects in mixture were evaluated in two conditions. Position number one indicates the arrangement of geotextile. This means, at first, one geotextile layer was embedded in the middle of materials. Then, two and three geotextile layers in equal depths from each other were used in soil mixtures. Position number two shows the mixing pieces randomly. This means that geotextile pieces in 1×1 and 5×5 cm2 were prepared and were randomly mixed with materials in 1, 2 and 3 percentages (by weight). For evaluating geotechnical behavior of improved clay-gravel mixtures, compaction and California bearing ratio test (CBR) (in dry and saturate conditions) based on ASTM were performed.
It should be noted CBR test in dry and saturate conditions were carried out in three different compaction energies (i.e. 10, 25 and 56 blow count for per layer). Moreover, CBR was evaluated for piston penetration at 2.5 and 5 cm in the specimen.
Results and discussion
The findings of this study could be summarized as:
1. Results of compaction test showed that, in the unimproved position, with increasing gravel content in clay, maximum dry unit weight (γdmax) has been increased, while simultaneous optimum water content (wopt) decreased.
In the improved position, in the first mode, when a geotextile layer was embedded in the middle of the specimens, γdmax reached to its upper value, whereas wopt reached to its minimum value. On the other hand, with an increase in the number of geotextile layers in clay-gravel mixtures, dry density has been decreased, but optimum water content increased. Furthermore, in the second mode, when geotextile pieces with 1×1 and 5×5 cm2 were randomly mixed in the specimens, the findings revealed that geotextile pieces with 1 cm2 areas and 1% by weight in clay-gravel mixtures increases γdmax and reduces wopt.
2. In dry and saturate conditions, California bearing ratio (CBR) test result displayed that in the unimproved condition, with an increase in gravel content in the clay, CBR value has been increased. In the improved situation, in the first mode, when a geotextile layer was embedded in the samples, CBR had a maximum value in all of the compaction energies even though it is reduced as the number of layers increased. In the second mode, when geotextile pieces in 1×1 cm dimensions with 1% (by weight) were randomly mixed with the specimens, CBR value reached at high. In contrast, with increasing dimensions of pieces and percentages in the presence of geotextile in clay-gravel mixtures, CBR values declined. Therefore, it can be concluded that, according to Code 234 (Iran Highway Asphalt Paving Code), the application of one geotextile sheet in the middle of materials or geotextile pieces in 1×1 cm dimensions with 1% (by weight) random mixing is suitable for subbase and base layers in pavement design.
3. CBR test results in the saturate condition in clay-gravel mixtures illustrated that, in the non-reinforced condition, with an increase in clay content in specimens, swelling value keeps rising sharply. On the contrary, in the reinforced position with embedding a geotextile layer in the middle sector of samples or through adding geotextile pieces (1 cm2) with 1 % content (by weight) to the specimens, the rate of swelling significantly decreased.
Conclusion
To sum up, the main objective of the present study was to investigate the impact of geotextile applications on bearing capacity of clay-gravel mixtures in pavement layers. The findings demonstrated that when geotextile as a layer was embedded in the middle part of specimens or as pieces with 1×1 cm dimensions and 1% content (by weight) was randomly mixed with the mid materials, the bearing capacity of the reinforced specimens was enhanced. In contrast, in the saturate condition, swelling potential significantly was reduced. It is noteworthy to mention that 1 cm2 pieces of geotextile is more effective than the layers. This is due to the fact these pieces make aggregates closer to each other. Thereby, minimum void ratio (emin) reaches its least value, the structure of grading improves, and the contacts between particles and geotextile pieces rise. As a suggestion for further research, it looks promising to evaluate the dynamic properties and the behavior of the improved materials with other geosyntheticses.
Moslem Babaei, Ali Raeesi Estabragh, Jamal Abdollahi, Mohadeseh Amini, Gholamali Vakili,
Volume 14, Issue 3 (11-2020)
Volume 14, Issue 3 (11-2020)
Abstract
Introduction
Expansive soils are a very common cause of extreme damages because they are susceptible to volume change due to a change in water content. Geotechnical problems associated with the expansive soils are well documented in different literature. As a result, a clear understanding of the behavior of such soils is required for the effective design of structures and infrastructures on these soils. The effects of hydrocarbon pollutants as a flooding fluid on the swelling potential of an expansive soil during wetting and drying cycles have not been considered in the previous researches. The aim of this research is to study the properties of an expansive soil with different flooding fluids, i.e. distilled water and solutions of glycerol with 10 and 20% through a number of cycles of wetting and drying tests under constant surcharge pressure.
Material and methods
The soil that was used in this work was a highly expansive clay soil (according to the classification by McKeen (1992)). It was prepared by mixing 20% bentonite and 80% kaolin. This soil was classified as a clay with high plasticity according to the Unified Soil Classification System (USCS). The optimum water content in the standard compaction test was 18.11% and the maximum dry unit weight was 16.27 kN/m3.
Distilled water and solutions of glycerol with concentrations of 10 and 20% were used for flooding the samples. To prepare the glycerol solutions, the required amount of glycerol was mixed with distilled water.
For making compacted samples for testing, the needed air-dried soil was weighed and the required water was added to it to reach the desired water content (4% below the optimum water content according to the compaction curve). The soil and water were mixed by hand and then was kept in a plastic bag for 24 hours to allow the uniform distribution of moisture in the soil. Samples were prepared by static compaction of the moist soil in a special mould.
A conventional oedometer was modified to allow the wetting and drying tests to be conducted under controlled surcharge pressure and temperature. During wetting and drying, the vertical deformation of the sample was measured by using a dial gauge. The variation of water content with void ratio during wetting and drying cycles was determined by using the information from the duplicated samples.
Results and discussion
Fig. 1 shows the variations of vertical deformation during wetting and drying cycles for samples that were flooded with distilled water and solutions of 10 and 20% glycerol. This figure illustrates that by increasing the number of cycles the amount of irreversible deformation is reduced until the equilibrium condition is achieved where the deformation due to wetting and drying is nearly the same. These results indicate that by increasing the concentration of glycerol the equilibrium condition with reversible deformation is reached in a fewer cycle of wetting and drying than the sample that was flooded with distilled water.
Figure 1. Wetting and drying cycles for different quality of flooding fluids
The results of void ratio versus water content at the equilibrium conditions for the samples flooded with distilled water and solutions of 10 and 20% glycerol (that were obtained from duplicated samples) are shown in Fig. 2. This figure displays that the paths of drying-wetting for different flooding fluids are nearly S-shaped curves. It is also seen in this figure that the order of the curves in this space is dependent on the percent of glycerol, the curves for the sample flooded with distilled water and 20% glycerol are located at the top and bottom of the space of void ratio against water content.
Figure 2. Water content-void ratio paths for different quality of flooding fluids
The change in the thickness of the diffuse double layer (DDL) affects on the swelling behavior of soil. The thickness of DDL is dependent on factors such as valency and concentration of cations, temperature, and dielectric constant. The value of dielectric constant for water is 80 and for solutions of 10 and 20% glycerol are 74.9 and 71.8, respectively. The magnitude of the attractive and repulsive forces between clay particles are inversely and directly depended on the value of the dielectric constant. The reduction in the value of the dielectric constant causes an increase in the attractive forces and leads to a reduction in the thickness of DDL. When the flooding fluid is a solution of glycerol, the initial chemical composition of pore fluid in the sample is changed. The chemical composition of pore fluid has different effects on the structure of clay soil such as changes in the thickness of DDL. When the flooding fluid is distilled water the pore fluid of samples has a dielectric constant of about 80. Therefore, the values of attractive and repulsive forces are not changed because of the same dielectric constant of flooding fluid and pore fluid. The results of tests on these samples (flooded with distilled water) show that by repeating the wetting and drying cycles the potential of swelling is reduced and after several cycles a reversible equilibrium condition is attained as depicted in Fig.1. When the pore fluid is the solution of glycerol, the attractive forces are increased due to the reduction of the dielectric constant of pore fluid and causes a reduction in the thickness of DDL. The shrinking of DDL is led to the formation of flocculated structure in the soil and results in pasting of particles together leading to the reduction potential of swelling. When the concentration solution of glycerol is increased the dielectric constant is decreased, the magnitude of attractive forces is increased and the degree of flocculation of the soil structure is increased that is yielded to a reduction of swelling potential.
Conclusion
Effect of different flooding fluids on the properties of an expansive soil during wetting and drying cycles were studied. The following conclusions can be drawn from the present research:
-After a number of wetting and drying cycles, the observed irreversible deformation was diminished and equilibrium was achieved. The solution of glycerol causes more reduction in the potential of swelling than distilled water.
-The wetting and drying paths in the space of void ratio and water content are S-shaped curves. The variations in the void ratio of samples flooded with the solution of glycerol are smaller than distilled water../files/site1/files/142/babaei.pdf
Hadi Fattahi, Younes Afshari,
Volume 14, Issue 3 (11-2020)
Volume 14, Issue 3 (11-2020)
Abstract
Introduction
Drill-bit selection is one of the most important aspects of well planning due to the bearing it can have on the overall cost of the well. Bit selection in conventional and slightly inclined wells is a very delicate and complex process. In high angle and horizontal wells it is even more difficult. Historically, drilling engineers have selected bits on the basis of what has been worked well in the area and what has been determined to have the lowest cost run from offset bit records. Often the best bit records were not available for evaluation, because the best bit may not yet have been run, may have been run by a competitor or the engineer was new to the area. As a result the bit program was generally developed by trial and error and at significant additional costs for a large number of wells. In most cases the optimum program was never reached because there was nothing to predict that a bit selection change could further reduce the cost of the well. In this study, an alternative solution approaches using the concept of the power of data mining algorithms to solve the optimum bit program for a given field is proposed.
Material and methods
It has been considered an offset well to be drilled outside the known boundaries of a known field. For this purpose, the seventh well (X-7) of the same field was used as a verification point. The data was trained using the well log and rock bit data of six wells located in the field and the real well log data of well 7 was input as unknown data. These depths are selected based on reported rock bit program. When compared to the real data, it could be observed that the models (adaptive neuro fuzzy inference system, K-nearest neighbors, decision tree, Bayesian classification theory and association rules) estimate
Results and discussion
In this paper, data mining algorithms for optimum rock bit program estimation is proposed. The accuracy and efficiency of the developed data mining algorithms (adaptive neuro fuzzy inference system, K-nearest neighbors, decision tree, Bayesian classification theory and association rules) that requires sonic and neutron log data input was tested for several real and synthetic cases. In the case of a development? well to be drilled outside the known boundaries of a field the model estimated rock bits with properties that consider the formation hardness correctly but slightly underestimated further rock bit details. The models also produced reasonable rock bit programs for an advance well to be drilled within the known boundaries of a field and a wildcat well drilled in a nearby field with similar rock properties to the training field. Thus it was concluded that the developed adaptive neuro fuzzy inference system is suitable as a front-end system for rock bit selection that could help engineers in decision-making analysis.
Conclusion
Optimum bit selection is one of the important issues in drilling engineering. Usually, optimum bit selection is determined by the lowest cost per foot and is a function of bit cost and performance as well as penetration rate. Conventional optimum rock bit selection program involves development of computer programs created from mathematical models along with information from previously drilled wells in the same area. Based on the data gathered on a daily basis for each well drilled, the optimum drilling program may be modified and revised as unexpected problems arose. The approaches in this study uses the power of data mining algorithms to solve the optimum bit selection problem. In order to achieve this goal, adaptive neuro fuzzy inference system, K-nearest neighbors, decision tree, Bayesian classification theory and association rules were developed by training the models using real rock bit data for several wells in a carbonated field. The training of the basic models involved use of both gamma ray and sonic log data. After that the models were tested using various drilling scenarios in different lithologic units. It was observed that the adaptive neuro fuzzy inference system model has provided satisfactory results.
Ali M. Rajabi, Shima Bakhshi Ardakani,
Volume 14, Issue 4 (12-2020)
Volume 14, Issue 4 (12-2020)
Abstract
Introduction
Improving the geotechnical characteristics of soils including superficial or deep soils has always been a challenge to geotechnical engineers. Therefore, various physical and chemical methods are used to improve different types of soils. In general, any physical, chemical, biological or combination of methods are used to change the characteristics of natural soil mass in order to achieve engineering goals which is defined in the "soil stabilization." Among different types of additives for soil stabilization, the use of pozzolans has been investigated by researchers because of their chemical compatibility with the environment and the cementation products due to chemical reactions. Todays, a lot of researches has been done on the use of natural or artificial zeolites as pozzolanic materials for the production of cement mixtures. This material, as a pozzolan, increases the speed of the pozzolanic reactions and reduces the density of cement products. However, many studies have been done to investigate the effect of zeolite and sepiolite on the resistance of cement products such as concrete, but so far, the use of these additives has been less considered for soil improvement. On the other hand, because of the compatibility of zeolite and sepiolite with the environment and their unique physiochemical properties, it is necessary to pay attention to these additives in order to improve the soil. Therefore, in this research, the effect of zeolite and sepillot additives with different percentages at different treatment times have been investigated to determine the elasticity modulus and hydraulic conductivity with focus on soil microstructure behavior.
Materials and methods
1. The properties of the soils
In this research, two types of soil including clayey sand (with 20% clay) and sandy clay (with 51% of clay) were used. The studied soils were a mixture of clay and sand of Firoozkouh (a typical type of sand located in north of Iran). Some physiochemical properties of zeolite and sepiolite are presented in Table 1.
Table 1. Physiochemical properties of zeolite and sepiolite used in this study
| L.O.I. | Na2O | K2O | MgO | CaO | Fe2O3 | Al2O3 | SiO2 | Chemical component | |
| 25.11 | 0.02 | 0.01 | 15.73 | 0.01 | o.61 | 0.3 | 55.3 | Sepiolite (%)S | |
| 11.94 | 0.13 | - | 0.87 | 2.45 | 1.26 | 13.54 | 69.74 | Zeolite (%) |
The uniaxial compressive strength tests were performed at 0.1 mm/min according to ASTM D2166 standard. The stabilized soil samples were compacted at percentages of 0, 5, 10, 15, 20 and 25 in cylindrical molds (38mm × 76mm) in five layers to achieve the desired density. In order to investigate the effect of curing time, the samples were placed inside sealed containers and underwent the test at instantaneous, 7, 14, and 28 days and at the desired additive percentages. To investigate the effect of additives on the soil hydraulic conductivity, clayey sand soil with additives 5, 10, 15, 20, and 25% was prepared using dry mixing method. Then, the prepared mixture was poured from a specific height into the permeability mold with a height of 8.65 cm and diameter of 5 cm. In this way, the specific dry unit weight of all samples was obtained as 1.47 g/cm3, close to the minimum specific dry unit weight. In this research, concerning the considerable effect of fine-grained soils on hydraulic conductivity, falling head test was used to determine the permeability coefficient.
In order to the morphology of the clayey sand soil without additives and stabilized with additives 15% was examined through SEM test.
Discussion and results
1. Modulus of elasticity
In this study, after uniaxial tests in different percentages and ages, the stress-strain graphs were plotted and then the elasticity modulus was calculated. The results showed that, with increasing zeolite content, the modulus of elasticity has been increased and, with increasing curing time, except for a slight decrease, after 7 days, the modulus of elasticity increased. During the initial treatment (7 days), the hardness of the sandy clay soil decreased and then increased with increasing time. In general, hardness in both soils in the high percentages of zeolite is significantly is increased.
Also, the effect of sepiolite on the modulus of elasticity has been studied. The results indicate that with the increase in the percentage of additive and lengthening the curing time, the modulus of elasticity is increased. This increase in the stabilization of both sandy clay and clayey sand soil is almost the same. In addition, in the case of sepiolite modification, the elasticity of sandy clay and clayey sand is approximately equal to 5 times in comparison to the initial value of unstabilized soil. However, in zeolite, the modulus of elasticity in clayey sand soils is almost 2 times, and sandy clay is nearly 5 times higher.
2. Permeability
To investigate the effect of additives on the soil hydraulic conductivity, clayey sand soil with additives 5, 10, 15, 20, and 25% was prepared using dry mixing method. The samples were saturated in a short period and permeability test was carried out immediately. Permeability coefficient changes were mostly influenced by physical factors. Therefore, due to the fineness of both types of additives, the hydraulic conductivity decreases with increasing additive content. The amount of reduced hydraulic conductivity in sepiolite stabilization is greater than zeolite due to the structure of the sepiolite (fiber-shaped) compared to zeolite.
3. SEM imaging
In this study, attempts were made to examine the reasons behind the obtained results more carefully through SEM imaging.
c b a
Figure 1. SEM image of non-stabilized clayey sand soil (a) soil stabilized with zeolite 15% (b) soil stabilized with sepiolite 15% (c) during the curing time of 28 days at magnifications 10000X
Figure 1a displays the SEM image of non-stabilized clayey sand soil. As can be seen in the figure, the soil structure is clear as layered and clay scales can be seen as laminated. Figure 1b demonstrates the SEM images of clayey sand soil stabilized with zeolite 15% during the curing time of 28 days. The sample has lost its layered structure in response to stabilization with zeolite during the curing time and changed into an integrated structure. This can be due to incidence of chemical reactions such as ion exchange and pozzolanic reactions in response to adding zeolite. Figure 1c demonstrates the SEM images of clayey sand soil stabilized with sepiolite 15% during the curing time of 28 days. As shown in the figure, the sepiolite has a fibrous-shaped structure that is longitudinally twisted. Also, with curing time increase, complex structures have emerged that could be due to the occurrence of chemical reactions.
Conclusion
This study examined the effect of zeolite and sepiolite additives on strength parameter of clayey soils. Accordingly, uniaxial compressive strength test was performed on clayey sand and sandy clay soil at percentages of 0, 5, 10, 15, 20 and 25% of zeolite and sepiolite with instantaneous curing times of 7, 14 and 28 days. Further, permeability test was conducted at different percentages on stabilized clayey sand soil. Also, to investigate the effect of these materials on soil microstructure, SEM imaging was performed at 28 days. The results show that both additives increase the elastic modulus of clayey sand and sandy clay soils. Also, the results indicate a steady increase in the stiffness of the cured soil with sepiolite during processing time. However, reducing soil hardness can be seen in stabilizing with zeolite at lower rates and lower percentages. In permeability test, hydraulic conductivity decreases with increasing additive content. The rate of permeability reduction in sepiolite is higher than zeolite. SEM images show that chemical reactions create an integrated structure that ultimately increases uniaxial compressive strength and modulus of elasticity. Also, SEM imaging depicts physical changes along chemical reaction in soil stabilized with sepiolite. Ultimately, increasing soil strength resulting from additive alongside environmentally friendliness is recommended in superficial and deep improvement of soil../files/site1/files/144/Rajabi.pdf
Vahid Shirgholami, Mahdi Khodaparat, Abolghasem Moezi,
Volume 14, Issue 4 (12-2020)
Volume 14, Issue 4 (12-2020)
Abstract
Introduction
Excavation in urban areas occasionally is accompanied by the improper performance of the support system for even small deformations. In this regard, deformation control design based on force-based approaches provides a more realistic reprehensive of excavation performance. Top-down deep excavation techniques are among the modern excavation stabilization methods in urban areas. In this method, unlike the conventional methods, it is possible to perform the excavation and construction operations simultaneously. The present study aims to investigate excavation stabilization using the main structure through the top-down approach. For this purpose, field and numerical evaluations of the stabilized project were conducted based on the top-down approach in the downtown of Qom city, Iran. This research reports the information obtained through monitoring and modeling using the finite element ABAQUS software, predicting the occurred deformations until the end of excavation operations using the calibrated model, and offering an initial estimation of the required stiffness for the support system with respect to the lateral deformations in four sites proposed, according to the studies of Line A Qom Subway.
Project specifications
Based on the geological studies of Line A Qom Subway Tunnel, the geological layers are classified into four soil classes. Qc-1 consists of gravely sand with fine content of 5 to 20%; Qc-2 is silty and clayey sand with fine content of 35 to 60%; Qf-1 is clayey silt with fine content of 60%; and Qf-2 is a silty clay layer with fine content above 60%. Line A of Qom subway passes the study area of the present study, which is located in Ammar e Yaser Street (Station A6). Based on the geotechnical studies of the project site, the site in the levels near the ground consists of Qc-2 but in the lower elevations, it is composed of Qc-1 and Qf-2.
Salam Trade Complex, located in the downtown of Qom city, has 6 underground stories and 6 above-ground stories. It is limited to the main street in the south and to urban decay in the three other directions. The final excavation depth, length, and width is -21, 36, and 32-52 m, respectively. The project structure consists of a steel moment frame with a retaining wall in the negative elevations and metal deck frame for ceiling construction. In this project, excavation wall deformation was monitored in three important sections (A, B, and C). Due to the vicinity to urban decay, a total station TS02 was used for monitoring these sections. According to the field surveys, the maximum horizontal deformation of the walls in sections A, B, and C is 24.10, 42.16, and 47.21 mm, respectively, which were measured in the 0, -1.5, and 0 m elevations.
Monitoring process and numerical simulation
To calibrate the prepared model, a sensitivity analysis was performed on geotechnical parameters including modulus of elasticity (E), internal friction angle (φ), and cohesion (C) of the layers by simulating 60 numerical models. Based on the sensitivity analysis results, an increase in internal friction angle and elasticity modulus for layer 1 (i.e., φ1 and E1) and elasticity modulus of layer 3 (E3) results in a decrease in lateral deformation. Finally, using the sensitivity analysis results and after several trials and errors, the numerical models for sections B and C were calibrated when reaching the depths of -8 and -11 m, respectively. Using these models, then, it is possible to predict deformations up to the end of the project.
To determine the required stiffness for the excavation support system, regarding the acceptable deformation of the adjacent soil mass, 160 numerical models were built and their results were analyzed. Based on the results of Brason and Zapata (2012), relative stiffens (R) were used to develop a relationship between the maximum lateral deformation of the wall and the required stiffness of the support system. R is a dimensionless parameter that represents the stiffness of a solid support system; the greater this value is, the more flexible the system would be. In this study, caisson pile length, excavation width, and buried depth of the wall were used for determining the R.
R =
(1)Figure 2 presents the maximum occurred deformation in terms of depth versus the relative stiffness for sites QC and QF.
Figure 2. Maximum deformation in terms of depth versus the relative stiffness for sites QC and QF
Conclusion
- According to the monitory data, the maximum lateral deformation in sections B and C until the end of the project was 42.16 and 47.2 mm, respectively. Moreover, the deformation of the other points inside the excavation was 30 mm.
- Considering the occurrence of maximum lateral deformations in the higher elevations in the monitored sections, it is inferred that excavation support at the ground level plays a key role in this approach. Hence, the lack of completing the structural frames and slabs for facilitating the excavation operation can lead to an increase in deformation levels.
- Based on the prepared graphs, the top-down approach in sites QC-2 and QF-2, compared to sites QF-1 and QC-1, provides a more desirable performance for deformation control.
Soheil Ghareh, Kimiya Yazdani, Fatemeh Akhlaghi,
Volume 14, Issue 4 (12-2020)
Volume 14, Issue 4 (12-2020)
Abstract
Introduction
The existence of problematic soils due to their geotechnical properties, such as low strength and stability, high compressibility, and swelling, is one of the most important issues and challenges that geotechnical and civil engineers are faced in urban environments, especially in metropolises. Various methods are used to stabilize and to improve the behavior of problematical soils such as compaction, consolidation, stone columns, jet grouting, biological procedures, and additive materials including nanomaterials. Because of their high specific surface, the use of nanoparticles is very effective to increase the shear and mechanical strength parameters of soil. Mashhad city is located on alluvial deposits of Mashhad Plain. A wide area of this city, especially the central and eastern areas where the Imam Reza holy shrine is located, has been built on weak and fine-grained deposits. Considering constructing high-rise buildings such as hotels and commercial complexes in these areas, as well as the need for restructuring the urban decay, the soil improvement will be inevitable. Given the significant application of these nanoparticles, the purpose of this study is to investigate the effects of nanoclay and nanosilica on each other and to find their optimal composition as a suitable alternative for traditional materials to improve the weak and problematic soils. This not only increases the bearing capacity and strength properties but also reduces the cost and time of project implementation.
Method and Materials
To achieve a hybrid with maximum strength and bearing capacity in executable projects, laboratory tests were performed on the soil picked up from the vicinity around Razavi holy shrine in Mashhad mixed with nanoclay and nanosilica. The type of soil is classified as CL-ML based on sieve and hydrometer tests. The nanoclay used in this research is the type of montmorillonite- K10, and the nanosilica is as a powdered shape with 99% purity.
At first, nanoclay and nanosilica were mixed independently with soil in six different weight ratios (0%, 0.1%, 0.5%, 1%, 2.5%, & 5%) and (0%, 0.1%, 0.25%, 0.5%, 0.75%, & 1%). Soil mechanical and strength properties, including compressive and shear strength, settlement, plasticity index, and swelling, were studied by standard laboratory tests on all specimens. After determining the optimum ratio of each nanoparticle, four hybrids consisting of nanosilica and nanoclay were made in four different combinations and then the effects of these four hybrids were investigated on the soil in the laboratory scale (Table 1).
Table 1. Composition of hybrids made with different percentages of nanomaterials
| Nanomaterials composition | Hybrid Name |
| 5% Nanoclay + 0.25% Nanosilica | 5NC + 0.25NS |
| 5% Nanoclay 1% Nanosilica | 5NC + 1NS |
| 2.5% Nanoclay + 0.25% Nanosilica | 2.5NC + 0.25NS |
| 2.5% Nanoclay + 1% Nanosilica | 2.5NC + 1NS |
The results of the Atterberg limit test on improved and pure soil indicate that the addition of nanoclay and nanosilica and the optimized ratios of these nanoparticles hybrid to increase the soil resistance parameters did not change the soil swelling index.
Evaluation of shear strength test results showed a significant synergistic effect of these nanoparticles on increasing the shear strength parameters. The nanoparticles hybrid of 2.5% nanosilica and 1% nanosilica increased the cohesion up to 106% and also hybrids of 5% nanosilica and 1% nanosilica increased the internal friction angle of soil up to 32%.
Examination of unconfined compressive strength tests presented a 134% increase in the compressive strength of the specimen improved with 2.5% nanoclay and a 620% increase in soil improved with 1% nanosilica. The optimum hybrid compositions of 5% nanoclay and 1% nanosilica increased significantly the compressive strength of the studied soil up to 785% and reduced the settlement of the soil by 60% compared to pure soil.
- Laboratory studies of electron microscopy examination on pure and improved soil samples with nanoparticle hybrid revealed the presence of these particles in pores of the improved soil. On the other hand, the high specific surface area of the nanoparticles increased the interaction of the soil particles, and the effect of adding these nanoparticles on the refining process is observed in compressive strength increase.
Maziar Hosseini, Majid Taromi, Mahdi Saeidi, Vahid Soleimani, Mehdi Soltani Negar,
Volume 14, Issue 4 (12-2020)
Volume 14, Issue 4 (12-2020)
Abstract
Introduction
Series A of coarse-grained alluvial deposits of Tehran are extended in eastern and north-eastern areas of Tehran. Analyzing and studying of these alluvial deposits from a geological point of view as well as their creation time and general characteristics such as the deposits’ mineral types, their source, and formation conditions, gives a better point of view to geotechnical engineers about exploring their characteristics as well as geotechnical aspects in underground structure design, excavations, and foundation design processes. On the other hand, in order to analyze stability, estimating the factor of safety and the seismic design of these structures, considering their location, which is in Tehran with a high seismic hazard area, the necessity of knowing the exact mechanical and dynamic properties of Tehran's alluvium is felt more than ever.
Material and methods
Due to the grain size of Tehran’s coarse-grained alluviums (series A) as well as high level of cementation of them, it is impossible (or maybe so difficult) to make undisturbed samples in order to do experiments. Such that it is excavated 23 boreholes with 30 to 140 meters depth as well as 17 test wells with 20 meters depth in an area which was extended in 10 kilometers in long which were located in Tehran’s No. 13 and No. 14 districts (as it can be seen in Figure 1). During the excavation of the entrance ramp and tunnel of eastern highway of Tehran, in-situ tests have been done in different sequences. Since it was important to investigate real behavior of these alluviums, different in-situ tests such as plate load test, in-situ shear test, pressuremeter test, and downhole test have been done as well as many laboratory and field tests. Furthermore, (1) X-Ray Diffraction (XRD) and (2) X-ray Fluorescence (XRF) as well as (3) Scanning Electron Microscopy (SEM) methods, have been used to explore the type of minerals and those used in cementation.
(ب)
Figure 1. a) Geological plan and the location of boreholes and test wells in the alignment of East Tehran Freeway
Results and discussion
Based on the results of XRD tests, it is quite clear that the largest weight percentages of tested samples are lime and silica.
Calcium and magnesium levels-as the high-power cations in flocculation process-in soil sample No. 1 (soil with high cementation level) are much more than soil sample No. 2 (soil with moderate cementation level).
This is the cause of high cementation level of soil sample No. 1 comparing with soils sample No. 2. A rapid increase in stress level can be seen in in-situ shear test results, in low shear displacements, up to reaching a maximum of τp (peak point) and afterwards reduction in shear stress with softening behavior.
Cohesion and shear strength levels also increase by increasing the depth. According to the plate load tests results, an increase in soil modules changes can be seen in different depths by depth increasing.
Large tendencies to increase in volume and dilation can be seen in under shear load cemented soils, after applying a primary compression on them. A brittle behavior with the occurrence of a certain peak can be seen in cemented samples. The significant increase in strength is directly related to the severe dilation rate, which can be seen in cemented samples results. The shear strength would be decreased, if this cement is broken during the particles’ displacements.
The results of downhole tests are shown in Figure 2. According to this figure, it has been explored that Vs,30 is about 600 m/s in moderate cemented soils while it is about 850 m/s in highly cemented soils. Because of the homogeneity and uniformity of sedimentary deposits, shear wave velocity is increasing due to the higher density of the layers and high level of cementation in both of the soil types. However, this increase is not significant at depths above 25 meters.
Conclusion
Based on the results, cementation level of the eastern coarse-grain-alluvium of Tehran is moderate to high and minerals used in cementation of this type of soil are generally carbonated and especially calcite.
Investigating the level of cementation of soil as well as the results of chemical analysis and in-situ tests, it can be found that the strength and deformation parameters of the soil are directly related to the degree of its cementation.
Based on the obtained results, the deformation modulus increases by about 25%, the cohesion by about 55% and the shear wave velocity by about 30% with increasing the degree of cementation (Table 1).
Increases of these parameters are directly related to depth. However, the cementation level does not significantly affect the internal friction angle of the soil.
Table 1. Average results of in-situ shear tests
| Deformation Modulus (MPa) | Peak Friction Angle (deg.) | Cohesion (kPa) |
USCS | Depth (m) |
Sample |
| 50-60 | 39 | 30-35 | GW-GM | 5 | Moderately Cemented Soil (M.C. Soil) |
| 75-85 | 41 | 50-60 | SP-SC | 10 | |
| 85-90 | 41 | 50-60 | GW-GC | 15 | |
| 95-105 | 41 | 50-60 | GW-GC | 20 | |
| 60-70 | 39 | 35-40 | GW-GM | 5 | Highly Cemented Soil (H.C. Soil) |
| 75-85 | 39 | 50-60 | GW-GC | 10 | |
| 110-120 | 42 | 65-75 | GW-GC | 15 | |
| 125-140 | 41 | 110-120 | GC | 20 |
Ali Akbar Moomeni, Ming Tao, Alireza Taleb Beydokhti,
Volume 14, Issue 4 (12-2020)
Volume 14, Issue 4 (12-2020)
Abstract
Introduction
Shallow tunnels have a vital role in urban planning, railway and highway transportation lines. The presence of underground cavities can lead
Mehdi Zamani, Ali Nikjoo,
Volume 14, Issue 5 (12-2020)
Volume 14, Issue 5 (12-2020)
Abstract
A jointed rock mass presents a more complex design problem than the other rock masses. The complexity arises from the number (greater than two) of joint sets which define the degree of discontinuity of medium. The condition that arises in these types of rock masses is the generation of discrete rock blocks, of various geometries. They defined by the natural fracture surfaces and the excavation surface. Stability problems in blocky jointed rock are generally associated with gravity falls of blocks from the roof and sidewalls. Whereas for block defined in the crown of tunnel,the requirement is to examine the potential for displacement of each block under the influence of the surface tractions arising from the local stress field and the gravitational load, in this paper various types of wedge formation in the crown of tunnel due to intersection of joint sets with various dip were examined. The state of stability of the wedge was then assessed through the factor of safety against roof failure. Following that the formed wedges in New York city and Washington D.C tunnels crown were investigated with limiting equilibrium analytical method and by use of Hoek and Brown failure criterion. The obtained results from analytical method corresponded with field observation.
Mr. Seyed Ali Ghaffari, Prof. Amir Hamidi, Dr. Gholamhossein Tavakoli Mehrjardi,
Volume 14, Issue 5 (12-2020)
Volume 14, Issue 5 (12-2020)
Abstract
This paper investigates response of triangular shell strip footings situated on the sandy slope. A series of reduced-scale plate load tests were conducted to cover different parameters including three shell footing types with different apex angles in addition to a flat footing, four different distances for strip footings from the crest of the slope namely “edge distance” and reinforcement status (unreinforced and geotextile-reinforced statuses). Bearing capacity of shell footings adjacent to crest of the slope, bearing capacity ratio, shell efficiency factor, influence of apex angle on settlement of footings and the mechanism of slope failure are discussed and evaluated. Also, empirical equations for determination of the maximum bearing capacity of triangular shell strip footings are suggested. As a whole, it has been observed that decrease of shell’s apex angle as good as increase of edge distance could significantly improve the bearing capacity. However, as the edge distance increases, the effect of apex angle on the bearing capacity got decreased. Also, it was found out that the beneficial effect of reinforcement on the bearing capacity decreased with increase of the edge distance. Furthermore, the efficiency of shell footings on bearing capacity was attenuated in reinforced slopes compared to the unreinforced status.
Mr. Mohammad-Emad Mahmoudi-Mehrizi, Prof Ali Ghanbari,
Volume 14, Issue 5 (12-2020)
Volume 14, Issue 5 (12-2020)
Abstract
The use of piles, helical anchors and, in general, helical foundations has considerably increased in the last 30 years. The adoption of this technology in the international and domestic codes of each country, as well as in research and studies, and, finally, the publication of numerous books and papers in this area, and the existence of manufacturers’ products, committees, and contractors of this technology has contributed to its expansion and development. However, such methods have progressed at a very slow pace in many countries, especially in developing countries. This paper attempts to assess the global advancement of the helical foundations by reviewing 292 papers from 1990 to 2020 and comparing the related research findings. This will help clarify the issue and determine the scope of technological progress. On the other hand, collecting valuable papers in this area will make it easier for researchers to make further research. Subsequently, the characteristics of this technology are highlighted and the reasons for its lack of progress in the developing countries are addressed. For this purpose, a questionnaire is sent to researchers, developers, designers, and contractors of the geotechnical projects. The purpose of this questionnaire is to specify the type of existing projects, the soil type of project site, the degree of familiarity with the helical foundation technology, the reasons for not using this method and the solutions available to expand and develop this method. Finally, there are suggestions to develop this approach and the issues that need further research.
Mohammad Maleki, Mohammad Amin Farahpour,
Volume 15, Issue 1 (5-2021)
Volume 15, Issue 1 (5-2021)
Abstract
Introduction
Grouting is one of the most widely used methods of soils improvement in which pressurized grout penetrates in the voids, of the soil. In the grouting method, in addition to reducing the permeability, shear strength and stiffness of the soil increase significantly. However, application of this method in projects such as dam construction and soil improvement requires the use of a large volume of grouting materials in order to satisfy the design criteria. In more recent years, due to the economic and environmental issues, in the case of cement-based grouts, replacing the whole or a portion of Portland cement with other materials has been experimentally investigated. A special type of kaolinite clay called metakaolin has recently been used in concrete, which has yielded interesting results. However, few studies has been conducted on the use of metakaolin in cement-based grouts. Such that, its effect on the mechanical behavior of the grouted soil are not well understood. Accordingly, in the present study, the mechanical behavior of a type of sandy soil grouted with different combinations of Portland cement and metakaolin was experimentally investigated in laboratory scale.
Material and methods
Different materials used in the present study including sand, cement, metakaolin, bentonite and water were selected based on the standard criteria and with the aim of better interpreting the test result and their differences due to considered influencing factors. Sand was obtained from Malayer Shushab river bed. According to the Unified Soil Classification System (USCS), it is classified as SP. Ordinary Portland cement was used in this study regarding to its widespread application in the practical works. The metakolin is classified as class N pozzolan according to the ASTM C618. Another constituent material of grout is bentonite which is produced by Iran Barit factory as sodium-calcium bentonite. Its liquid limit and plastic index are 296 and 262 percent, respectively. The water used to prepare the grouts was provided from Hamedan drinking water, which according to ASTM C94 has the required quality for grouting operations in laboratory.
The device for grouting specimens was developed at the Soil Mechanics Laboratory of Bu-Ali Sina University during the present study. It equipped with grouting pressure control system and tool for keeping grout in homogeneous conditions during the grouting operation into specimen. The samples were prepared with 0, 5, 10, 15, 20 and 25 percent substitution of cement with metakaolin. Curing time of grouted samples was considered as14 and 28 days.
In order to investigate the factor affecting stress-strain behavior of the grouted sand, the samples were sheared using advanced triaxial apparatus. After passing considered curing time, the samples were sheared considering three levels of confining pressures of 50, 100 and 200 kPa and by applying axial strain rate of 1 mm per minute. For each test, the maximum deviator stress and its corresponding axial strain were recorded. In addition, for studying post peak behavior of grouted soil, for every one of tests, average ratio of deviator stress to the axial strain as softening modulus, was calculated from the deviator stress-axial strain curves. The moisture content of the samples was also measured according to ASTM D2216 at the end of tests. In the following, the role of different factors influencing stress-stain behavior of grouted sand including
Results and discussion
Figure 1 shows the effect of metakaolin as alternative of a portion of cement on maximum confined compressive strength and its corresponding axial strain.
For the samples confined by pressure of 50 kPa the maximum confined compressive strength is almost constant by replacing cement with metakaolin up to 10%. However, the amount of axial strain corresponding to the maximum compressive strength of the specimens increases by 6% (Figure 2). For 25% replacement, the maximum confined compressive strength of the samples decreases by 17% compared to the initial state (pure cement). In contrast, the axial strain value related to peak state of most samples has been increased by 4% in comparison to the initial state.
In the case of confining pressure of 100 kPa, by replacing up to 10%, the mean confined compressive strength of the specimens was almost constant. However, the amount of axial strain corresponding to the peak state of the specimens has been increased by a maximum value of 18%. For 20% replacement percentage the compressive strength of the specimens has been decreased by about 15% compared to the initial state. However, in the range of 20 to 25 percent, the reduction process has slowed down, which can be due to various factors such as the effects of sample densification during further increase of metakaolin. According to Figure 1, it can be seen that in the range of 20 to 25% substitution, the amount of strain at failure state increased by an average of 40%, which indicates that the sample is more deformable.
In the case of confining stress of 200 kPa, by replacing 10% of the cement with metakaolin, maximum confined compressive strength and its corresponding axial strain, has been increased by approximately 5 and 14%, respectively. With increasing cement substitution up to 25%, the resistance of the specimens decreased by 8% compared to the result of sample grouted with pure cement. Although, axial strain at peak state has been increased by 28%. From
Conclusion
The aim of this study was to investigate, in laboratory scale, the mechanical behavior of sand grouted with cement-based grout and considering different percentage of metakaolin as an alternative for a portion of cement. The soil samples were grouted using a specific device developed during present study. After passing curing time the samples were sheared using triaxial apparatus by considering three levels of confining pressures. The main findings of this experimental research are as follows:
- Replacing 10% of cement with metakaolin, increases deformability of grouted soil, without reducing compressive strength. Deformability of grouted soil increases with adding more percentage of metakaolin however, in this case compressive strength decreases.
- By increasing confining pressures, more values of metakaolin can be used instead of cement in the grout.
- Increasing confining pressure, increases compressive strength, increases deformability and deceases softening modulus at post peak behavior.
- Shear strength parameters of grouted sand is affected by adding metakaolin into the grout. Increasing the percentage of metakaolin results in small changes in the internal friction angle of the grouted sand, however, the amount of cohesion decreases.
Majid Aslani, Javad Nazariafshar,
Volume 15, Issue 1 (5-2021)
Volume 15, Issue 1 (5-2021)
Abstract
Introduction
Stone column installation method is one of the popular methods of ground improvement. Several studies have been performed to investigate the behavior of stone columns under vertical loads. However, limited research, mostly focused on numerical investigations, has been performed to evaluate the shear strength of soil reinforced with stone column. The stress concentration ratio (n) is one of the important parameters that uses in soil improvement by stone column method. Stress concentration ratio is the ratio of the stress carried by stone column to that carried by the surrounding soil. In this paper, the results of a laboratory study were used to examine the changes in the stress concentration ratio when normal and shear stress applied. Direct shear tests were carried out on specimens of sand bed material, stone column material and sand bed reinforced with stone column, using a direct shear device with in-plane dimensions of 305*305 mm and height of 152.4 mm. Experiments were performed under normal stresses of 55, 77 and 100 kPa. In this study, three different area replacement ratios (8.4%, 12%, 16.4%), and three different stone column arrangements (single, square and triangular) were considered for investigation. Loose sand and crushed gravel were used to make the bed and stone columns, respectively. In this study, the equivalent shear strength and equivalent shear parameters measured from experiments were also compared with those predicted by analytical relationships at stress concentration value of 1 and stress concentration value obtained from experiments.
Material Properties
Fine-grained sand with particle size ranging from 0.425 to 1.18 mm was used to prepare loose sand bed, and crushed gravel with particle size ranging from 2 to 8 mm was used as stone column material. The sand material used as bed material had a unit weight of 16 kN/m3 and a relative density of 32.5%, and the crushed stone material used in stone columns had a unit weight of 16.5 kN/m3 and a relative density of 80%. The required standard tests were performed to obtain the mechanical parameters of bed material and stone column material. As the diameters of model scale stone columns were smaller than the diameters of stone columns installed in the field, the particle dimensions of stone column material were reduced by an appropriate scale factor to allow an accurate simulation of stone columns behavior.
Testing Procedure
In this study, large direct shear device was used to evaluate the shear strength and equivalent shear strength parameters of loose sand bed reinforced with stone column. Experiments were performed under normal stresses of 55, 75 and 100 kPa. Two class C load cells with capacity of 2 tons were used to measure and record vertical forces and the developed shear forces during the experiments, and a Linear Variable Differential Transformer (LVDT) was used to measure horizontal displacement. The main objectives of this study was to calculate the stress concentration ratio of stone columns in different arrangement. Stress concentration ratio is the ratio of the stress carried by stone column to that carried by the surrounding soil, and can be calculated using Equation 1. For this purpose, the direct shear device was modified. Two miniature load cells with capacity of 5 kN were employed. The load cells were mounted on the rigid loading plate with dimensions of 305*305 mm2 and thickness of 30 mm, as shown in Figure 1, All achieved data from the experiments including data on vertical forces, shear forces and horizontal displacements were collected and recorded using a data logger, and an especial software was used to transfer data between the computer and the direct shear device. All specimens were sheared under a horizontal displacement rate of 1 mm/min.
Results and discussion
- The SCR value increases for settlement up to 3 mm and then decreases with increasing the horizontal displacement and then approaches almost a constant value. Results also show that stress concentration ratio decreases with increase of stone column diameter. Results show that the value of stress concentration ratio in square pattern is higher than that in single and triangular pattern. Moreover, results show that stress concentration ratio decreases with increase of normal stress.
- The value of the internal friction angle in (peak) state, for loose bed increases from 33 to 40 degrees in square arrangement and in the corresponding state of displacement of 10 % from 30 degrees in a loose bed increase to 32 degrees, for loose sand reinforced with stone column. Shear strength increases with the increase of modified area ratio in all stone column installation patterns in both the peak and the corresponding state of the horizontal displacement of 10%.
- For stone columns with the same modified area ratio, the installation pattern has an effective role in defining the shear strength. Group stone columns mobilize higher shear strength compared to single stone columns. Among the installation patterns investigated in this study, stone columns with square arrangement experienced the highest increase in shear strength value while single stone columns experienced the lowest.
- The equivalent shear strength values measured from experiments are higher than those obtained from analytical relationships. Accordingly, it is conservative to use analytical relationships to calculate shear strength parameters. It is worth explaining that these relationships assume that the value of stress concentration ratio is equal to 1. Results from this study show that the value of stress concentration ratio should be accurately calculated and used in the relationships.
- Comparison between shear strength parameters obtained from experiments and those predicted by analytical relationships shows that in single stone columns, the value of stress concentration ratio should be 3 to 4.5, and in square and triangular patterns, this value should be 6 to 7 and in triangular patterns 4.5 to 5, respectively, to achieve good agreement between experimental and analytical results in peak condition. In horizontal displacement 10% the value of stress concentration ratio should be 2.5 to 3, in single, square and triangular patterns, to achieve good agreement between experimental and analytical results../files/site1/files/151/2.pdf
Mohammad Hossein Keyghobadi, Adel Asakereh, Behzad Kalantari, Masoud Dehghani,
Volume 15, Issue 1 (5-2021)
Volume 15, Issue 1 (5-2021)
Abstract
Introduction
The ring footings are very important and sensitive due to widespread use in various industries such as oil and gas; so finding some ways for improving the behavior of these types of footings can be very valuable. One of these ways, which is very affordable and also can be help in environmental protection, is the use of granulated rubber that made from disposable materials like scrape tires, as the soil reinforcement. In the present study, the behavior of ring footings with outer constant diameter of 300 mm and variable inner diameters (90, 120 and 150 mm with inner to outer diameter ratio of 0.3, 0.4 and 0.5) placed on unreinforced sand bed and also granulated rubber reinforced bed, has been investigated by field test. The effects of important parameters like inner to outer diameter ratio of ring footing and thickness of rubber-soil mixture on the behavior of ring footing in terms of bearing capacity, settlement and inside vertical stresses of footing bed have been studied and the optimum values mentioned parameters have been determined.
Material and methods
In all tests, a sandy soil was used to fill the test trench which was excavated in the natural bed of the earth with a length and width of 2000 mm and a height of 990 mm. It should be noted that the type of this soil is well-graded sand (SW) according to the Unified Classification System (ASTM D 2487-11). This sand had medium grain size, D50, of 2.35 mm, moisture content of 5.4% and friction angle of 41.7∘. The granulated rubber particles with dimensions between 2-20 mm, a mean particle size, D50, of 14 mm and a specific gravity, Gs, of 1.15, have been used in all tests for using in rubber-soil mixture layer.
The loading system consists of several parts such as loading frame for providing reaction force, hydraulic jack, load cell, load transfer system (including loading shaft which was located below Load cell and footing cap which was located under the loading shaft) and rigid steel loading plates with different inner to outer diameter ratios (d/D=0.3, 0.4 and 0.5 and constant outer diameter of 300 mm). Some devices like load cell, LVDT, pressure cell, data logger and unit control were applied to collect the data and control the system. Both soil and rubber-soil mixture layers were compacted by vibrating plate compactor to gain their maximum densities. After preparing the tests, the static load was applied on the system at a rate of 1 kPa per second until 1000 kPa or until backfill failure.
Results and discussion
The results of tests on both unreinforced and rubber reinforced beds indicated that the ring footing with inner to outer diameter ratio (d/D) of 0.4 had the maximum bearing capacity in all settlement levels. This behavior can be related to the arching phenomenon within the internal spaces of ring footing with optimum inner to outer diameter ratio. In fact, when the ring footing with optimum inner to outer diameter ratio is subjected to a certain level of loading, the soil inside the ring seems to be compacted due to interface effect of the two sides of the ring. However, by increasing the inner to outer diameter ratio more than its optimum value, the ring behaves like two independent strip footings without any interface effect and therefore the bearing capacity decreases.
The results of tests showed that the vertical inside stresses in different depths of footing bed (both unreinforced and rubber reinforced beds) decrease with increasing d/D ratio. This stress reduction process can be due to the transfer of stress concentration from the points close to the center of the ring to the outer point because of turning from the ring mode with interface effect to the two independent strip footings that mentioned earlier.
The results of rubber reinforced cases illustrated that, regardless of the footing settlement level and also irrespective of d/D ratio, the bearing capacity of ring footing increases with increasing the thickness of rubber-soil mixture layer (hrs) up to the value equals 0.5 times the outer diameter of ring footing and further increase in this thickness more than mentioned optimum value (hrs/D=0.5) can decrease the bearing capacity. Even in some cases of reinforced base (hrs/D=1), the bearing capacity can be reduced to the value less than that of unreinforced cases. It can be due to high compressibility of rubber reinforced layers with higher thicknesses than optimum value.
It should be mentioned that the rubber reinforced layer can reduce the vertical inside stresses compared to unreinforced cases. It can be due to this fact that the rubber reinforced layer acts as a wide slab. Such that it can spread the applied loading over a wider area. Also rubber reinforced layer has high capacity of absorbing energy and therefore can decrease the vertical inside stresses.
Conclusion
In the present study the behavior of ring footing placed on rubber reinforced bed have been investigated by field test. The effect of different parameters such as inner to outer diameter ratio of ring footing and the thickness of rubber-soil mixture layer on the bearing capacity, settlement and vertical inside stresses of the footing bed were studied. The result indicates that:
- In both unreinforced and rubber reinforced bed, the ring footing with inner to outer diameter ratio (d/D) of 0.4 had the maximum bearing capacity, regardless of settlement level.
-The vertical inside stresses in different depths of footing bed decrease with increasing d/D ratio.
-The bearing capacity of ring footing increases with increasing the thickness of rubber-soil mixture layer (hrs) up to the optimum value equals 0.5 times the outer diameter of ring footing.
-The vertical stresses can be reduced by using rubber reinforced layer../files/site1/files/151/5.pdf
Related Websites
Site Keywords
نشریه, Academic Journal, Scientific Article, کلمه شماره یک, کلمه شماره یک, کلمه شماره یک, کلمه شماره یک, کلمه شماره دو, کلمه شماره یک, کلمه دوVote
© 2024 CC BY-NC 4.0 | Journal of Engineering Geology
Designed & Developed by : Yektaweb